#SERVICE TRACCAR INSTALLED HOW TO#
#SERVICE TRACCAR INSTALLED SERIAL NUMBER#
#SERVICE TRACCAR INSTALLED BLUETOOTH#

When you have the appropriate integration with Node-RED and the EarthRanger application running, the FMT100 should show up in Earth Ranger with the device name.I can see right now my biggest mistake was watching the video, I am trying to purge my brain and just start all over, I am trying to figure out how to remove all traces of Traccar from my home computer and two cell phones so I can start all over and hopefully sort this all out.Ĭan you direct me to the directions for removing everything, all traces of Traccar from all my devices then direct me to the step by step instructions on installation and setup, I need the FOR DUMMIES instructions, I think my fatal mistake was the quick install, the quick install must assume many things about me my computer and my devices. This will trigger the accelerometer of the FMT100. In case nothing is happening, trigger the FMT100 to send a new position messages by shaking or moving it. The traccar dashboard will now show the incoming positions and other data of your FMT100. Enter a Name and use the 15 digit IMEI number as the Identifier.It is time to add the device to the traccar server. Now we have the FMT100 configured, connected to the 2G network and connected to the traccar server.

#SERVICE TRACCAR INSTALLED SERIAL NUMBER#

Copy the Device IMEI number → 15 digit serial number (xxxxxxxxxxxxxxx).Check and change other settings according to your application.Server Settings → Add the address and port of the traccar server.GPRS Settings → add your APN credentials.Go to the GPRS settings and change the following settings:.Open the Teltonika Configurator, scan for devices and connect to the FMT100.Connect the FMT100 to you computer with USB.Power the FMT100 with a 10 - 30 V DC power source.Connect the provided back-up battery to the FMT100.Many M2M service providers like 1nce will offer a nice management portal for your subscriptions. Just make sure you know the APN settings of the subscription and if enabled the PIN for the SIM used. There are many M2M Connectivity providers, but for this example we have used 1nce. Before we can add this unit to Traccar, we need to make sure it is equipped with a working SIM-card with access to the 2G network in your area of deployment. This device works out of the box with Traccar and is easy to integrate into the Smart Parks Stack. Solid waterproof case and built-in accelerometer sensor with extremely accurate crash trace functionality makes this device perfectly suitable for insurance market solutions. FMT100 is equipped with special clamp connector for fast power cable connection to the car battery. Biggest in its class internal High Gain GNSS antenna allows mounting directly on car battery under the hood.

#SERVICE TRACCAR INSTALLED BLUETOOTH#

The Teltonika FMT100 is a small, smart and waterproof GNSS SPECIAL tracker with 2G and Bluetooth connectivity and internal backup battery. When you have the appropriate integration with Node-RED and the EarthRanger application running, the position of the smartphone should show up in EarthRanger with the given device name. This will ensure the App starts sending positions. In case nothing is happening, check if the Server status is enabled in the Client App. The traccar dashboard will now show the incoming positions and other data of from your smartphone.

Use the Extra → Category field to indicate what the device is tracking.

Use the Extra → Model field to indicate what device type this is.

Enter a Name and use the Device identification number from the Traccar Client as the Identifier.

For testing it is nice to set it to a low frequency like 30 seconds.

Change the other settings, like the GPS frequency (interval) according to your application.

Add the Server URL and make sure it points to your Tracker server.

Copy the Device identification number from the Tracker Client App.

Install the Tracker Client on your phone and in your browser open your Traccar dashboard. The easy and fast way to test your Traccar deployment is to use the Traccar Client App on your smartphone.

push the Earth Ranger formatted payloads to the EarthRanger flow.

use a function node to convert the JSON payloads coming from traccar to the EarthRanger format.

HTTP IN PUSH node listening to /traccar/positions and another one for /traccar/events.

Add the traccar integration flows to your Node-RED.

Add the following lines to the nf file.

Here we will only focus briefly on the most coming way to integrate with the Smart Parks Stack trough Node-RED. There are many ways to integrate with the Traccar Server. Adding Traccar to the Smart Parks Stack offers users to integrate all major GPS tracking devices into all used Applications like EarthRanger and Grafana. Traccar is the leading GPS tracking software.

Service traccar installed